Fastest Cable Modem Factory – Fiber Node Transponder, SA120IE – MoreLink
Short Description:
Product Detail
Product Tags
Related Video
Feedback (2)
Fastest Cable Modem Factory – Fiber Node Transponder, SA120IE – MoreLink Detail:
Cable Modem Features
▶DOCSIS/EURODOCSIS 1.1/2.0/3.0, Channel bonding: 8*4
▶Two MCX (Female) connectors for Downstream and Upstream
▶Provide two-Port Giga Ethernet MDI Signals to target board (Digital Board) through J1 & J2
▶Get DC Power Supply from Target Board by use of J2
▶Standalone External Watchdog
▶Temperature sensor on board
▶Small size (dimensions): 113mm x 56mm
▶Accurate RF power level 2dB at all temperature range
▶FBC for Spectrum Analyzer, integrated Splendidtel Spectrum Analyzer (SSA)
▶Support Low Power Mode and Full Function Mode Switchable
SW Features
▶DOCSIS®/Euro-DOCSIS® HFC environment auto detection
▶UART/I2C/SPI/GPIO driver customization for various devices monitoring. Such as Fiber node, Power Supply, RF Amplifier
▶Docsis MIBs / Any other customized MIB support
▶Open system API and data structure for 3rd party application’s access
▶Low power signal detection. Signal lower than -40dBmV will be represented with built-in Spectrum Analyzer
▶CM MIB Files are open for customers
▶CM management Web GUI is available on WAN or LAN
▶MSO can reboot the CM remotely via Telnet or SNMP
▶Switchable between Bridge and Router mode
▶Supports DOCSIS device upgrade MIB
System Block
External Watchdog
An external watchdog is used to make sure the system’s operation reliably. Watchdog is kicked by the
Firmware every once in a while, so that the CM does not reset. If there’s something wrong with the CM
Firmware, then after a certain period (watchdog time), the CM will reset automatically.
Technical Parameters
| Protocol Support | ||
| ◆ DOCSIS/EuroDOCSIS 1.1/2.0/3.0◆ SNMP v1/v2/v3◆ TR069 | ||
| CPU and Memory | ||
| CPU | BCM33838M (8×4, Commercial, 0 ~ +70 oC)BCM3383DI (8×4, Industrial, -40 ~ +85 oC) | |
| Memory | 64MB DDR3 | |
| Flash | 8MB SPI Flash | |
| Connectivity | ||
| RF: MCX1, MCX2 | Two MCX Female, 75 OHM, Straight Angle, DIP | |
| Ethernet Signal/PWR: J1, J2 | 1.27mm 2×17 PCB Stack, Straight Angle, SMD2xGiga Ethernet Ports | |
| RF Downstream | ||
| Frequency (edge-to-edge) | ◆ 88~1002 MHz (DOCSIS)◆ 108~1002 MHz (EuroDOCSIS) | |
| Channel Bandwidth | ◆ 6 MHz (DOCSIS)◆ 8 MHz (EuroDOCSIS)◆ 6/8 MHz (Auto Detection, Hybrid Mode) | |
| Modulation | 64QAM, 256QAM | |
| Data Rate | Up to 400 Mbps by 8 Channel bonding | |
| Signal Level | Docsis: -15 to +15 dBmVEuro Docsis: -17 to +13 dBmV (64QAM); -13 to +17 dBmV (256QAM) | |
| RF Upstream | ||
| Frequency Range | ◆ 5~42 MHz (DOCSIS)◆ 5~65 MHz (EuroDOCSIS)◆ 5~85 MHz (Optional) | |
| Modulation | TDMA: QPSK,8QAM,16QAM,32QAM,64QAMS-CDMA: QPSK,8QAM,16QAM,32QAM,64QAM,128QAM | |
| Data Rate | Up to 108 Mbps by 4 Channel Bonding | |
| RF Output Level | TDMA (32/64 QAM): +17 ~ +57 dBmVTDMA (8/16 QAM): +17 ~ +58 dBmVTDMA (QPSK): +17 ~ +61 dBmVS-CDMA: +17 ~ +56 dBmV | |
| Networking | ||
| Network protocol | IP/TCP/UDP/ARP/ICMP/DHCP/TFTP/SNMP/HTTP/TR069/VPN (L2 and L3) | |
| Routing | DNS / DHCP server / RIP I and II | |
| Internet Sharing | NAT / NAPT / DHCP server / DNS | |
| SNMP version | SNMP v1/v2/v3 | |
| DHCP server | Built-in DHCP server to distribute IP address to CPE by CM’s Ethernet port | |
| DCHP client | CM automatically gets IP and DNS server address from MSO DHCP server | |
| Mechanical | ||
| Dimensions | 56mm (W) x 113mm (L) | |
| Environmental | ||
| Power Input | Support wide power input: +12V to +24V DC | |
| Power Consumption | 12W (Max.)7W (TPY.) | |
| Operating Temperature | Commercial: 0 ~ +70 oC Industrial: -40 ~ +85 oC | |
| Operating Humidity | 10~90% (Non Condensing) | |
| Storage Temperature | -40 ~ +85 oC | |
Board-to-Board Connectors between Digital and CM Board
There’re two boards: Digital board and CM Board, which use four pairs of board-to-board connectors to transmit RF signals, Digital signals and power.
Two pairs of MCX connectors used for DOCSIS Downstream and Upstream RF Signals. Two pairs of Pin Header/PCB Socket used for Digital Signals and Power. CM board is placed under the Digital Board. CM’s CPU is contacted to the housing through thermal pad to transfer the heat away from CPU and towards the housing and environment.
The mated height between two boards is 11.4+/-0.1mm.
Here’s the illustration of matched board-to-board connection:
Note:
Cause of Board-to-Board design for two PCBA Boards, in order to make sure stable and reliable connection, therefore, when
To design the Housing, it should be taken the assembly engineering and screws for fix into consideration.
MCX1, MCX2: 75 OHM, Female, Straight Angle, DIP
MCX1: DS
MCX2: US
Matched MCX Male: 75 OHM, Male, Straight Angle, DIP
J1, J2: 2.0mm 2×7 PCB Socket, Straight Angle, SMD
J1: Pin Definition (Preliminary)
|
J1 Pin |
CM Board |
Digital Board |
Comments |
|
1 |
GND |
||
|
2 |
GND |
||
|
3 |
TR1+ |
Giga Ethernet Signals from CM board. There’s NO Ethernet transformer on the CM board, here’re Only the Ethernet MDI Signals to Digital Board. RJ45 and Ethernet transformer are placed at Digital Board. |
|
|
4 |
TR1- |
||
|
5 |
TR2+ |
||
|
6 |
TR2- |
||
|
7 |
TR3+ |
||
|
8 |
TR3- |
||
|
9 |
TR4+ |
||
|
10 |
TR4- |
||
|
11 |
GND |
||
|
12 |
GND |
||
|
13 |
GND |
Digital board provides Power to CM board, the power level range is; +12 to +24V DC | |
|
14 |
GND |
J2: Pin Definition (Preliminary)
|
J2 Pin |
CM Board |
Digital Board |
Comments |
|
1 |
GND |
||
|
2 |
Reset |
Digital board can send a reset signal to CM board, then to reset the CM. 0 ~ 3.3VDC | |
|
3 |
GPIO_01 |
0 ~ 3.3VDC | |
|
4 |
GPIO_02 |
0 ~ 3.3VDC | |
|
5 |
UART Enable |
0 ~ 3.3VDC | |
|
6 |
UART Transmit |
0 ~ 3.3VDC | |
|
7 |
UART Receive |
0 ~ 3.3VDC | |
|
8 |
GND |
||
|
9 |
GND |
0 ~ 3.3VDC | |
|
10 |
SPI MOSI |
0 ~ 3.3VDC | |
|
11 |
SPI CLOCK |
0 ~ 3.3VDC | |
|
12 |
SPI MISO |
0 ~ 3.3VDC | |
|
13 |
SPI Chip Select 1 |
0 ~ 3.3VDC | |
|
14 |
GND |
PCB Dimension
Product detail pictures:
Related Product Guide:
Our pros are lessen prices,dynamic sales team,specialised QC,sturdy factories,top quality services and products for Fastest Cable Modem Factory – Fiber Node Transponder, SA120IE – MoreLink, The product will supply to all over the world, such as: Latvia, Australia, Estonia, With the development and enlargement of mass clients abroad, now we have set up cooperative relationships with many major brands. We have our own factory and also have many reliable and well-cooperated factories in the field. Adhering to the "quality first, customer first, We are provideing high-quality, low-cost products and first-class service to customers. We sincerely hope to establish business relationship with customers from all over the world on the basis of quality, mutually benefit. We welcome OEM projects and designs.
By Prudence from Peru - 2017.09.29 11:19
We are old friends, the company's product quality has been always very good and this time the price is also very cheap.
By Elaine from Bahrain - 2017.07.28 15:46
